Ohji flake

Flake Lining is a type of lining application in which a coating containing a substrate with mixtures of ultrathin glass flake and acid, alkali, solvent and gas-resistant thermosetting resin has been added.

SKU: OhjiFlake001 Categories: ,

Chemical Resistance of Flake Lining

Working Temperature

Working Condition

A Maximum allowable temperature 1 Liquid
B Maximum 700C 2 Splash
C Maximum 600C 2 Dry Gas
D Maximum 400C
T Confirmation Test Required
N Not Recommended

* In liquid: Soaking and Wet Gas, Out of liquid: Splash and Dry Gas

* Maximum Allowable Temperature (used approx. 30minutes per a day)

* 100 series is up to 149C

* 200 series is up to 188C

       Chemicals

Formula

Conc.

Series

100 200 300
Hydrochloric Acid HCL 1~20% B1 C2 C2
Hydrochloric Acid HCL 20~37% B2 C3 C3
Sulfuric Acid H2SO4 2~20% A1 T T
Sulfuric Acid H2SO4 20~50% B1 N N
Sulfuric Acid H2SO4 50~70% C1 N N
Sulfuric Acid H2SO4 70~80% T N N
Sulfuric Acid H2SO4 80~98% N N N
Sulfurous Acid H2SO3 saturation A1 D1 D1
Nitric Acid HNO3 5% B1 T T
Nitric Acid HNO3 10% C1 N N
Nitric Acid HNO3 25% D1 N N
Nitric Acid HNO3 40% D1 N N
Nitric Acid HNO3 60% D2 N N
Concentrated Nitric Acid HNO3 N N N
Nitrous Acid HNO2 C1 T T
Hydrofluoric Acid HF solution 1~10% T N N
Hydrofluoric Acid HF solution 10~53% N N N
Hydrosilicic Acid H2SiF6 T N N
Phosphoric Acid H3PO4 20% A1 T T
Phosphoric Acid H3PO4 saturation A1 T T
Chromic Acid CrO3 10% B1 N N
Hydroiodic Acid HI Solution 29% D1 T T
Hydrobromic Acid HBr Solution 20% D1 T T

Description

What’s FLAKE LINING

Flake Lining is a type of lining application in which a coating containing a substrate with mixtures of ultrathin glass flake and acid, alkali, solvent and gas-resistant thermosetting resin has been added.

In the resin, few microns of glass flakes are layered (see the image of water vapour permeability). They are not allowed to permeate chemicals and gas, even if their films are thin, due to the low water vapour permeability.

It features the small liner coefficient of expansion and further low shrinkage both during and after hardening. That increases adhesion to a steel substrate. Those stable properties provide robust protection against potential peering and cracks caused by repetitive use in high temperature

Reinforced Corrosion Protection Lining

Flake lining is anti-corrosive coating system for servere exposures. Flake compound is made from thermosetting liquid resin mixed with glass flakes in microns thick, and applied in a thickness of 0.5~3.0mm.

Glass flakes as barries fillers make the coating much more durable and prevent permeablility of corrosive substances, as the layers of laminated glass flakes (50~100 layers in 1mm thickness) form a highly impermable structure.

Feature of Flake Lining

  1. Excellent resistance to various acids, base, solvents & gases Very small vapor permeability
  2. Prevention of permeability
  3. Small shrinkage at curing
  4. Small thermal expansion
  5. Curing at room temp.
  6. Easily application at site
  7. Maintenance free
  8. Short time application

Flake lining has excellent chemical resistance against most of acid, base, solvent and gas. Type of resin could be selected in accordance to the kind of service chemical.

In general, following features are given for flake lining.

GOOD POINT 

  1. Easy field application – Material hardening at normal temperature
  2. Short application time – Easy for maintenance
  3. Excellent chemical resistance and high temperature service – Up to 150℃ for gas
  4. Reasonable cost

NOT GOOD POINT 

  1. Shock absorption – Combination of application with FRP reinforcement
  2. Abrasion resistance – Compounding with ceramic resin or rubber reinforcement
  3. Workmanship defect – Need to supervise workmanship during application and quality control

Our flake materials use for application has imported from OHJI (Japan) manufacture. We are provide flake materials or the supervisor which will be best suited for your needs.

Chemical Resistance of Flake Lining

Working Temperature

Working Condition

A Maximum allowable temperature 1 Liquid
B Maximum 700C 2 Splash
C Maximum 600C 2 Dry Gas
D Maximum 400C
T Confirmation Test Required
N Not Recommended

* In liquid: Soaking and Wet Gas, Out of liquid: Splash and Dry Gas

* Maximum Allowable Temperature (used approx. 30minutes per a day)

* 100 series is up to 149C

* 200 series is up to 188C

       Chemicals

Formula

Conc.

Series

100 200 300
Hydrochloric Acid HCL 1~20% B1 C2 C2
Hydrochloric Acid HCL 20~37% B2 C3 C3
Sulfuric Acid H2SO4 2~20% A1 T T
Sulfuric Acid H2SO4 20~50% B1 N N
Sulfuric Acid H2SO4 50~70% C1 N N
Sulfuric Acid H2SO4 70~80% T N N
Sulfuric Acid H2SO4 80~98% N N N
Sulfurous Acid H2SO3 saturation A1 D1 D1
Nitric Acid HNO3 5% B1 T T
Nitric Acid HNO3 10% C1 N N
Nitric Acid HNO3 25% D1 N N
Nitric Acid HNO3 40% D1 N N
Nitric Acid HNO3 60% D2 N N
Concentrated Nitric Acid HNO3 N N N
Nitrous Acid HNO2 C1 T T
Hydrofluoric Acid HF solution 1~10% T N N
Hydrofluoric Acid HF solution 10~53% N N N
Hydrosilicic Acid H2SiF6 T N N
Phosphoric Acid H3PO4 20% A1 T T
Phosphoric Acid H3PO4 saturation A1 T T
Chromic Acid CrO3 10% B1 N N
Hydroiodic Acid HI Solution 29% D1 T T
Hydrobromic Acid HBr Solution 20% D1 T T

Series 100

● OHJI FLAKE 100 SERIES (Heavy corrosion purpose, Thick type)

• Thickness:          Avg. 2mm (2coats)

• Method:              Trowel

• Application:         FGD duct & tank, Water treatment equip, Chemical tank

OHJI FLAKE 100 series

Base Resin

Average Volume

features

HF -141

Het acid Polyester resin

4 kg/m2

For oxidizing chemicals

HF – 161

Bis type Vinylester resin

4 kg/m2

Standard (1000C-Liquid)

HF – 181

Novolac type Vinylester resin

4 kg/m2

Heat resistance (1500C-Gas)

 

Chemical Resistance of Flake Lining

Working Temperature

Working Condition

A Maximum allowable temperature 1 Liquid
B Maximum 700C 2 Splash
C Maximum 600C 2 Dry Gas
D Maximum 400C
T Confirmation Test Required
N Not Recommended

* In liquid: Soaking and Wet Gas, Out of liquid: Splash and Dry Gas

* Maximum Allowable Temperature (used approx. 30minutes per a day)

* 100 series is up to 149C

* 200 series is up to 188C

       Chemicals

Formula

Conc.

Series

100 200 300
Hydrochloric Acid HCL 1~20% B1 C2 C2
Hydrochloric Acid HCL 20~37% B2 C3 C3
Sulfuric Acid H2SO4 2~20% A1 T T
Sulfuric Acid H2SO4 20~50% B1 N N
Sulfuric Acid H2SO4 50~70% C1 N N
Sulfuric Acid H2SO4 70~80% T N N
Sulfuric Acid H2SO4 80~98% N N N
Sulfurous Acid H2SO3 saturation A1 D1 D1
Nitric Acid HNO3 5% B1 T T
Nitric Acid HNO3 10% C1 N N
Nitric Acid HNO3 25% D1 N N
Nitric Acid HNO3 40% D1 N N
Nitric Acid HNO3 60% D2 N N
Concentrated Nitric Acid HNO3 N N N
Nitrous Acid HNO2 C1 T T
Hydrofluoric Acid HF solution 1~10% T N N
Hydrofluoric Acid HF solution 10~53% N N N
Hydrosilicic Acid H2SiF6 T N N
Phosphoric Acid H3PO4 20% A1 T T
Phosphoric Acid H3PO4 saturation A1 T T
Chromic Acid CrO3 10% B1 N N
Hydroiodic Acid HI Solution 29% D1 T T
Hydrobromic Acid HBr Solution 20% D1 T T

Series 200

 OHJI FLAKE 200 & 300 SERIES (Light corrosion purpose, Thin type Heavy corrosion purpose, Thick type)

• Thickness:           Avg. 800μm (200series)

                              Avg. 400μm (300series)

• Method:               Spray or Roller

• Application:         Oil tank, Seawater pipe, Ocean construction

OHJI FLAKE 200 series

Base resin

Average Volume

Features

HF-261

Bis type Vinylester resin

1.8 kg/m2

Standard (600C-liquid)

HF–281

Novolac type Vinylester resin

1.8 kg/m2

Heat resistance (1500C-Gas)

Chemical Resistance of Flake Lining

Working Temperature

Working Condition

A Maximum allowable temperature 1 Liquid
B Maximum 700C 2 Splash
C Maximum 600C 2 Dry Gas
D Maximum 400C
T Confirmation Test Required
N Not Recommended

* In liquid: Soaking and Wet Gas, Out of liquid: Splash and Dry Gas

* Maximum Allowable Temperature (used approx. 30minutes per a day)

* 100 series is up to 149C

* 200 series is up to 188C

       Chemicals

Formula

Conc.

Series

100 200 300
Hydrochloric Acid HCL 1~20% B1 C2 C2
Hydrochloric Acid HCL 20~37% B2 C3 C3
Sulfuric Acid H2SO4 2~20% A1 T T
Sulfuric Acid H2SO4 20~50% B1 N N
Sulfuric Acid H2SO4 50~70% C1 N N
Sulfuric Acid H2SO4 70~80% T N N
Sulfuric Acid H2SO4 80~98% N N N
Sulfurous Acid H2SO3 saturation A1 D1 D1
Nitric Acid HNO3 5% B1 T T
Nitric Acid HNO3 10% C1 N N
Nitric Acid HNO3 25% D1 N N
Nitric Acid HNO3 40% D1 N N
Nitric Acid HNO3 60% D2 N N
Concentrated Nitric Acid HNO3 N N N
Nitrous Acid HNO2 C1 T T
Hydrofluoric Acid HF solution 1~10% T N N
Hydrofluoric Acid HF solution 10~53% N N N
Hydrosilicic Acid H2SiF6 T N N
Phosphoric Acid H3PO4 20% A1 T T
Phosphoric Acid H3PO4 saturation A1 T T
Chromic Acid CrO3 10% B1 N N
Hydroiodic Acid HI Solution 29% D1 T T
Hydrobromic Acid HBr Solution 20% D1 T T

Series 300

 OHJI FLAKE 200 & 300 SERIES (Light corrosion purpose, Thin type Heavy corrosion purpose, Thick type)

• Thickness:           Avg. 800μm (200series)

                              Avg. 400μm (300series)

• Method:               Spray or Roller

• Application:         Oil tank, Seawater pipe, Ocean construction

OHJI FLAKE 300 series

Base resin

Average Volume

Features

HF-341

Het acid Polyester resin

1 kg/m2

For oxidizing chemicals

HF-361

Bis type Vinylester resin

1 kg/m2

Standard (550C-Liquid)

HF–381

Novolac type Vinylester resin

1 kg/m2

Heat resistance (1500C-Gas)

Chemical Resistance of Flake Lining

Working Temperature

Working Condition

A Maximum allowable temperature 1 Liquid
B Maximum 700C 2 Splash
C Maximum 600C 2 Dry Gas
D Maximum 400C
T Confirmation Test Required
N Not Recommended

* In liquid: Soaking and Wet Gas, Out of liquid: Splash and Dry Gas

* Maximum Allowable Temperature (used approx. 30minutes per a day)

* 100 series is up to 149C

* 200 series is up to 188C

       Chemicals

Formula

Conc.

Series

100 200 300
Hydrochloric Acid HCL 1~20% B1 C2 C2
Hydrochloric Acid HCL 20~37% B2 C3 C3
Sulfuric Acid H2SO4 2~20% A1 T T
Sulfuric Acid H2SO4 20~50% B1 N N
Sulfuric Acid H2SO4 50~70% C1 N N
Sulfuric Acid H2SO4 70~80% T N N
Sulfuric Acid H2SO4 80~98% N N N
Sulfurous Acid H2SO3 saturation A1 D1 D1
Nitric Acid HNO3 5% B1 T T
Nitric Acid HNO3 10% C1 N N
Nitric Acid HNO3 25% D1 N N
Nitric Acid HNO3 40% D1 N N
Nitric Acid HNO3 60% D2 N N
Concentrated Nitric Acid HNO3 N N N
Nitrous Acid HNO2 C1 T T
Hydrofluoric Acid HF solution 1~10% T N N
Hydrofluoric Acid HF solution 10~53% N N N
Hydrosilicic Acid H2SiF6 T N N
Phosphoric Acid H3PO4 20% A1 T T
Phosphoric Acid H3PO4 saturation A1 T T
Chromic Acid CrO3 10% B1 N N
Hydroiodic Acid HI Solution 29% D1 T T
Hydrobromic Acid HBr Solution 20% D1 T T

Reviews

There are no reviews yet.

Be the first to review “Ohji flake”

Your email address will not be published. Required fields are marked *